Description: This part of SIM 3281 presents data for the bathymetric contours for several seafloor maps (see sheets 1, 2, 3, 7, 10, SIM 3281) of the Offshore of Santa Barbara map area, California. The vector data file is included in "Contours_OffshoreSantaBarbara.zip," which is accessible from http://pubs.usgs.gov/ds/781/OffshoreSantaBarbara/data_catalog_OffshoreSantaBarbara.html. The bathymetry and shaded-relief maps of the Offshore of Santa Barbara map area, California, were generated from bathymetry data collected by California State University, Monterey Bay, Seafloor Mapping Lab (CSUMB), by the U.S. Geological Survey (USGS), and by Fugro Pelagos for the U.S. Army Corps of Engineers (USACE) Joint Lidar Bathymetry Technical Center of Expertise. Most of the offshore area was mapped by CSUMB in the summer of 2007, using a 244-kHz Reson 8101 multibeam echosounder. Smaller areas in the far-east nearshore, as well as further offshore to the west and in the southeast outer shelf area, were mapped by the USGS in 2005 and 2006, using a combination of 468-kHz (2005) and 117-kHz (2006) SEA (AP) Ltd. SWATHplus-M phase-differencing sidescan sonars. The nearshore bathymetry and coastal topography were mapped for USACE by Fugro Pelagos in 2009, using the SHOALS-1000T bathymetric-lidar and Leica ALS60 topographic-lidar systems. All these mapping missions combined to collect bathymetry from the 0-m isobath to beyond the 3-nautical-mile limit of California's State Waters. A smooth arithmetic mean convolution function that assigns a weight of one-ninth to each cell in a 3-pixel by 3-pixel matrix was then applied iteratively to the grid ten times. Following smoothing, contour lines were generated at 10-m intervals, then the contours were clipped to the boundary of the map area.
Description: This part of SIM 3281 presents data for folds for the geologic and geomorphic map (see sheet 10, SIM 3281) of the Offshore of Santa Barbara map area, California. The vector data file is included in "Folds_OffshoreSantaBarbara.zip," which is accessible from http://pubs.usgs.gov/ds/781/OffshoreSantaBarbara/data_catalog_OffshoreSantaBarbara.html. This map area lies within the Western Transverse Ranges geologic province, which is north of the California Continental Borderland (Fisher and others, 2009). This province has undergone significant north-south compression since the Miocene, and recent GPS data suggest north-south shortening of about 6 mm/yr (Larson and Webb, 1992). The active, east-west-striking Pitas Point Fault (a broad zone that includes south-dipping reverse faults), Red Mountain Fault, and Rincon Creek Fault are some of the structures on which this shortening occurs (see, for example, Jackson and Yeats, 1982; Sorlien and others, 2000; Fisher and others, 2009). This fault system, in aggregate, extends for about 100 km through the Ventura and Santa Barbara Basins and represents an important earthquake hazard (see, for example, Fisher and others, 2009).
Description: This part of SIM 3281 presents data for folds for the geologic and geomorphic map (see sheet 10, SIM 3281) of the Offshore of Santa Barbara map area, California. The vector data file is included in "Faults_OffshoreSantaBarbara.zip," which is accessible from http://pubs.usgs.gov/ds/781/OffshoreSantaBarbara/data_catalog_OffshoreSantaBarbara.html. This map area lies within the Western Transverse Ranges geologic province, which is north of the California Continental Borderland (Fisher and others, 2009). This province has undergone significant north-south compression since the Miocene, and recent GPS data suggest north-south shortening of about 6 mm/yr (Larson and Webb, 1992). The active, east-west-striking Pitas Point Fault (a broad zone that includes south-dipping reverse faults), Red Mountain Fault, and Rincon Creek Fault are some of the structures on which this shortening occurs (see, for example, Jackson and Yeats, 1982; Sorlien and others, 2000; Fisher and others, 2009). This fault system, in aggregate, extends for about 100 km through the Ventura and Santa Barbara Basins and represents an important earthquake hazard (see, for example, Fisher and others, 2009).
Description: This part of SIM 3281 presents data for the geologic and geomorphic map (see sheet 10, SIM 3281) of the Offshore of Santa Barbara map area, California. The vector data file is included in "Geology_OffshoreSantaBarbara.zip," which is accessible from http://pubs.usgs.gov/ds/781/OffshoreSantaBarbara/data_catalog_OffshoreSantaBarbara.html. The offshore part of the map area largely consists of a relatively shallow (less than 75 m deep), gently offshore-dipping (less than 1 degree) shelf underlain by sediments derived primarily from relatively small coastal watersheds that drain the Santa Ynez Mountains. Shelf deposits are primarily sand (unit Qms) at water depths less than about 35 to 50 m and, at depths greater than about 35 to 50 m, are the more fine-grained sediments (very fine sand, silt, and clay) of unit Qmsf. The boundary between units Qms and Qmsf is based on observations and extrapolation from sediment sampling (see, for example, Reid and others, 2006) and camera ground-truth surveying (see sheet 6). It is important to note that the boundary between units Qms and Qmsf should be considered transitional and approximate and is expected to shift as a result of seasonal- to annual- to decadal-scale cycles in wave climate, sediment supply, and sediment transport. Coarser grained deposits (coarse sand to boulders) of unit Qmsc, which are recognized on the basis of their high backscatter and, in some cases, their moderate seafloor relief (sheets 1, 2, 3), are found most prominently in a large (about 0.75 km2) lobe that is present from about 1,800 to 3,600 m offshore of the mouth of Arroyo Burro, in water depths of about 36 to 65 m. The lobe is inferred to consist of coarse-grained sediment (coarse sand to boulders) that is resistant to erosion. Although these coarse-grained deposits almost certainly are derived from Arroyo Burro, the lobe could represent either the underflow deposits of late Holocene floods or a relict geomorphologic feature, having been deposited in shallower marine deltaic (or even alluvial?) environments at lower sea levels in the latest Pleistocene and early Holocene. Unit Qmsc also is present in shallower water (depths of about 10 to 20 m), most notably in a small area (approximately 0.09 km2) that extends offshore from Montecito Creek, in the eastern part of the map area. The presence of coarser grained sediment (coarse sand and possibly gravel) also is inferred in shallower water (depths of 10 to 20 m) offshore from Arroyo Burro, but these deposits are mapped as unit Qmss because they are found within arcuate scour depressions that have been referred to as "rippled scour depressions" (see, for example, Cacchione and others, 1984; Phillips, 2007) or "sorted bedforms" (see, for example, Murray and Thieler, 2004; Goff and others, 2005; Trembanis and Hume, 2011). Although the general area in which Qmss scour depressions are found is not likely to change substantially, the boundaries of the unit(s), as well as the locations of individual depressions and their intervening flat sand sheets, likely are ephemeral, changing during significant storm events. Hydrocarbon-seep-induced topography, which is present most prominently along the axis of anticlines, includes many features (described by Keller and others, 2007) along the trend of the Mid-Channel Anticline, about 10 km south of the map area in the Santa Barbara Channel. Geologic map units associated with hydrocarbon emissions in the map area include grouped to solitary pockmarks (unit Qmp) and asphalt (tar) deposits (unit Qas), as well as areas of undifferentiated hydrocarbon-related features (unit Qhfu) that probably include a mix of mounds, mud volcanoes, pockmarks, carbonate mats, and other constructional and erosional "seabed forms" (see Keller and others, 2007), all of which are superimposed on consolidated, undivided Miocene and Pliocene bedrock (unit Tbu). Offshore bedrock exposures are assigned to the Miocene Monterey Formation (unit Tm) and to the undivided Miocene and Pliocene bedrock unit (Tbu), primarily on the basis of extrapolation from the onland geologic mapping of Minor and others (2009), as well as the geologic cross sections of Redin (2005). These cross sections, which are constrained by industry seismic-reflection data and petroleum well logs, suggest that a considerable part of the undivided bedrock unit may belong to the Pliocene and Pleistocene Pico Formation. Bedrock is, in some places, overlain by a thin (less than 1 m?) veneer of sediment, recognized on the basis of high backscatter, flat relief, continuity with moderate- to high-relief bedrock outcrops, and (in some cases) high-resolution seismic-reflection data; these areas, which are mapped as composite units Qms/Tbu or Qms/Tm, are interpreted as ephemeral sediment layers that may or may not be continuously present, depending on storms, seasonal and (or) annual patterns of sediment movement, or longer term climate cycles. The Santa Barbara Channel region, including the map area, has a long history of petroleum production (Barnum, 1998). The Monterey Formation is the primary petroleum-source rock in the Santa Barbara Channel, and the Pico Formation is one of the primary petroleum reservoirs. The bedrock units typically are exposed in structural highs that include uplifts associated with the partly blind(?), south-dipping Rincon Creek Fault Zone and the outer shelf anticlinal uplift that developed above the south strand of the Red Mountain Fault in the southwestern part of the map area. The Offshore of Santa Barbara map area is in the Ventura Basin, in the southern part of the Western Transverse Ranges geologic province, which is north of the California Continental Borderland (Fisher and others, 2009). This province has undergone significant north-south compression since the Miocene, and recent GPS data suggest north-south shortening of about 6 mm/yr (Larson and Webb, 1992). The active, east-west-striking Red Mountain and Rincon Creek Faults and their related folds are some of the structures on which this shortening occurs. This fault system, in aggregate, extends for about 100 km through the Ventura and Santa Barbara Basins and represents an important earthquake hazard (see, for example, Fisher and others, 2009). Very high uplift rates of onland marine terraces from More Mesa (2.2 mm/yr), in the western part of the map area, to Summerland (0.7 mm/yr), a few kilometers east of the map area, are further indication of rapid shortening in this region (Keller and Gurrola, 2000).
Description: This part of SIM 3281 presents data for the habitat map of the seafloor (see sheet 7, SIM 3281) of the Offshore of Santa Barbara map area, California. The vector data file is included in "Habitat_OffshoreSantaBarbara.zip," which is accessible from http://pubs.usgs.gov/ds/781/OffshoreSantaBarbara/data_catalog_OffshoreSantaBarbara.html. Using multibeam echosounder (MBES) bathymetry and backscatter data, potential marine benthic habitat maps were constructed. The habitats were based on substrate types and documented or "ground truthed" using underwater video images and seafloor samples obtained by the USGS. These maps display various habitat types that range from flat, soft, unconsolidated sediment-covered seafloor to hard, deformed (folded) or highly rugose and differentially eroded bedrock exposures. Rugged, high-relief, rocky outcrops that have been eroded to form ledges and small caves are ideal habitat for rockfish (Sebastes spp.) and other bottom fish such as lingcod (Ophiodon elongatus). Habitat map is presented in a map format generated in a GIS (ArcMap), and both digital and hard-copy versions will be produced.
Description: This part of SIM 3281 presents data for the seafloor-character map (see sheet 5, SIM 3281) of the Offshore of Santa Barbara map area, California. The raster data file is included in "SeafloorCharacter_OffshoreSantaBarbara.zip," which is accessible from http://pubs.usgs.gov/ds/781/OffshoreSantaBarbara/data_catalog_OffshoreSantaBarbara.html. This raster-format seafloor-character map shows six substrate classes of the Offshore of Santa Barbara map area. The six substrate classes mapped in this area have been colored to indicate which of the following California Marine Life Protection Act depth zones and slope classes they belong: Depth Zone 2 (intertidal to 30 m), Depth Zone 3 (30 to 100 m), and Slope Class 1, 0 degrees to 5 degrees (flat). Depth Zone 1 (intertidal), Depth Zones 4 and 5 (greater than 100 m), and Slope Classes 2 to 4, greater than 5 degrees (sloping to vertical) are not present in this map area. The map is created using a supervised classification method described by Cochrane (2008), available at http://doc.nprb.org/web/research/research%20pubs/615_habitat_mapping_workshop/Individual%20Chapters%20High-Res/Ch13%20Cochrane.pdf.
Description: This part of SIM 3281 presents data for the bathymetry and shaded-relief maps (see sheets 1, 2, SIM 3281) of the Offshore of Santa Barbara map area, California. The raster data file for the bathymetry map is included in "Bathymetry_OffshoreSantaBarbara.zip." The raster data file for the shaded-relief map is included in "BathymetryHS_OffshoreSantaBarbara.zip." Both are accessible from http://pubs.usgs.gov/ds/781/OffshoreSantaBarbara/data_catalog_OffshoreSantaBarbara.html. The bathymetry and shaded-relief maps of the Offshore of Santa Barbara map area, California, were generated from bathymetry data collected by California State University, Monterey Bay, Seafloor Mapping Lab (CSUMB), by the U.S. Geological Survey (USGS), and by Fugro Pelagos for the U.S. Army Corps of Engineers (USACE) Joint Lidar Bathymetry Technical Center of Expertise. Most of the offshore area was mapped by CSUMB in the summer of 2007, using a 244-kHz Reson 8101 multibeam echosounder. Smaller areas in the far-east nearshore, as well as further offshore to the west and in the southeast outer shelf area, were mapped by the USGS in 2005 and 2006, using a combination of 468-kHz (2005) and 117-kHz (2006) SEA (AP) Ltd. SWATHplus-M phase-differencing sidescan sonars. The nearshore bathymetry and coastal topography were mapped for USACE by Fugro Pelagos in 2009, using the SHOALS-1000T bathymetric-lidar and Leica ALS60 topographic-lidar systems. All these mapping missions combined to collect bathymetry from the 0-m isobath to beyond the 3-nautical-mile limit of California's State Waters.
Description: This part of SIM 3281 presents data for part of the acoustic-backscatter map (see sheet 3, SIM 3281) of the Offshore of Santa Barbara map area, California. The raster data file is included in "BackscatterA_CSUMB_OffshoreSantaBarbara.zip," which is accessible from http://pubs.usgs.gov/ds/781/OffshoreSantaBarbara/data_catalog_OffshoreSantaBarbara.html. The acoustic-backscatter map of the Offshore of Santa Barbara map area, California, was generated from backscatter data collected by California State University, Monterey Bay, Seafloor Mapping Lab (CSUMB) and by the U.S. Geological Survey (USGS). These metadata describe the acoustic-backscatter data collected by CSUMB and reprocessed by the USGS. See "BackscatterB_USGS_OffshoreSantaBarbara_metadata.txt" metadata for a description of the acoustic-backscatter data collected by the USGS. Most of the offshore area was mapped by CSUMB in the summer of 2007, using a 244-kHz Reson 8101 multibeam echosounder. Within the acoustic-backscatter imagery, brighter tones indicate higher backscatter intensity, and darker tones indicate lower backscatter intensity. The intensity represents a complex interaction between the acoustic pulse and the seafloor, as well as characteristics within the shallow subsurface, providing a general indication of seafloor texture and sediment type. Backscatter intensity depends on the acoustic source level; the frequency used to image the seafloor; the grazing angle; the composition and character of the seafloor, including grain size, water content, bulk density, and seafloor roughness; and some biological cover. Harder and rougher bottom types such as rocky outcrops or coarse sediment typically return stronger intensities (high backscatter, lighter tones), whereas softer bottom types such as fine sediment return weaker intensities (low backscatter, darker tones).
Description: This part of SIM 3281 presents data for part of the acoustic-backscatter map (see sheet 3, SIM 3281) of the Offshore of Santa Barbara map area, California. The raster data file is included in "BackscatterB_USGS_OffshoreSantaBarbara.zip," which is accessible from http://pubs.usgs.gov/ds/781/OffshoreSantaBarbara/data_catalog_OffshoreSantaBarbara.html. The acoustic-backscatter map of the Offshore of Santa Barbara map area, California, was generated from backscatter data collected by California State University, Monterey Bay, Seafloor Mapping Lab (CSUMB) and by the U.S. Geological Survey (USGS). These metadata describe the acoustic-backscatter data collected by the USGS. See "BackscatterA_CSUMB_OffshoreSantaBarbara_metadata.txt" metadata for a description of the acoustic-backscatter data collected by CSUMB. Small areas in the far-east nearshore, as well as further offshore to the west and in the southeast outer shelf area, were mapped by the USGS in 2005 and 2006, using a combination of 468-kHz (2005) and 117-kHz (2006) SEA (AP) Ltd. SWATHplus-M phase-differencing sidescan sonars. Within the acoustic-backscatter imagery, brighter tones indicate higher backscatter intensity, and darker tones indicate lower backscatter intensity. The intensity represents a complex interaction between the acoustic pulse and the seafloor, as well as characteristics within the shallow subsurface, providing a general indication of seafloor texture and sediment type. Backscatter intensity depends on the acoustic source level; the frequency used to image the seafloor; the grazing angle; the composition and character of the seafloor, including grain size, water content, bulk density, and seafloor roughness; and some biological cover. Harder and rougher bottom types such as rocky outcrops or coarse sediment typically return stronger intensities (high backscatter, lighter tones), whereas softer bottom types such as fine sediment return weaker intensities (low backscatter, darker tones).
Description: This part of SIM 3281 presents data for part of the acoustic-backscatter map (see sheet 3, SIM 3281) of the Offshore of Santa Barbara map area, California. The raster data file is included in "BackscatterA_USGS05_OffshoreSantaBarbara.zip," which is accessible from http://pubs.usgs.gov/ds/781/OffshoreSantaBarbara/data_catalog_OffshoreSantaBarbara.html. The acoustic-backscatter map of the Offshore of Santa Barbara map area, California, was generated from backscatter data collected by California State University, Monterey Bay, Seafloor Mapping Lab (CSUMB) and by the U.S. Geological Survey (USGS). These metadata describe the acoustic-backscatter data collected by the USGS. See "BackscatterA_CSUMB_OffshoreSantaBarbara_metadata.txt" metadata for a description of the acoustic-backscatter data collected by CSUMB. Small areas in the far-east nearshore, as well as further offshore to the west and in the southeast outer shelf area, were mapped by the USGS in 2005 and 2006, using a combination of 468-kHz (2005) and 117-kHz (2006) SEA (AP) Ltd. SWATHplus-M phase-differencing sidescan sonars. Within the acoustic-backscatter imagery, brighter tones indicate higher backscatter intensity, and darker tones indicate lower backscatter intensity. The intensity represents a complex interaction between the acoustic pulse and the seafloor, as well as characteristics within the shallow subsurface, providing a general indication of seafloor texture and sediment type. Backscatter intensity depends on the acoustic source level; the frequency used to image the seafloor; the grazing angle; the composition and character of the seafloor, including grain size, water content, bulk density, and seafloor roughness; and some biological cover. Harder and rougher bottom types such as rocky outcrops or coarse sediment typically return stronger intensities (high backscatter, lighter tones), whereas softer bottom types such as fine sediment return weaker intensities (low backscatter, darker tones).
Description: This part of SIM 3281 presents data for the bathymetry and shaded-relief maps (see sheets 1, 2, SIM 3281) of the Offshore of Santa Barbara map area, California. The raster data file for the bathymetry map is included in "Bathymetry_OffshoreSantaBarbara.zip." The raster data file for the shaded-relief map is included in "BathymetryHS_OffshoreSantaBarbara.zip." Both are accessible from http://pubs.usgs.gov/ds/781/OffshoreSantaBarbara/data_catalog_OffshoreSantaBarbara.html. The bathymetry and shaded-relief maps of the Offshore of Santa Barbara map area, California, were generated from bathymetry data collected by California State University, Monterey Bay, Seafloor Mapping Lab (CSUMB), by the U.S. Geological Survey (USGS), and by Fugro Pelagos for the U.S. Army Corps of Engineers (USACE) Joint Lidar Bathymetry Technical Center of Expertise. Most of the offshore area was mapped by CSUMB in the summer of 2007, using a 244-kHz Reson 8101 multibeam echosounder. Smaller areas in the far-east nearshore, as well as further offshore to the west and in the southeast outer shelf area, were mapped by the USGS in 2005 and 2006, using a combination of 468-kHz (2005) and 117-kHz (2006) SEA (AP) Ltd. SWATHplus-M phase-differencing sidescan sonars. The nearshore bathymetry and coastal topography were mapped for USACE by Fugro Pelagos in 2009, using the SHOALS-1000T bathymetric-lidar and Leica ALS60 topographic-lidar systems. All these mapping missions combined to collect bathymetry from the 0-m isobath to beyond the 3-nautical-mile limit of California's State Waters.